Mouth-actuated projectile toys carry a specific hazard: a child blows into the mouthpiece, and the projectile is supposed to launch forward. If the projectile can pass back through the mouthpiece instead, it becomes a choking risk. The Mouth-Actuated Catapult Tester applies a controlled air pressure to the mouthpiece and checks whether the projectile penetrates backward. This Mouth-Actuated Catapult Tester is built for toy manufacturers, third-party safety laboratories, and quality inspection departments that need a repeatable pass/fail check aligned with EN 71-1 requirements.

Technical Specifications

The Mouth-Actuated Catapult Tester is supplied as a single model, GT-M04-1, with the pressure control system, timer, and tube grippers configured as a complete benchtop test station.

GT-M04-1 Core Configuration

• Model/Part Number: GT-M04-1

• Test Air Pressure: 13.8 kPa ± 5%

• Hold Time: 5 seconds per cycle

• Testing Cycles: 10 times total

• Power Supply: AC 220V, 50Hz

• Application: Mouth-actuated projectile toys, checking blow-through resistance

• Reference Standard: EN 71-1 section 8.17.1 (per manufacturer's Spanish-language page)

• Test Principle: Place catapult into the mouth-actuated projectile toy, apply 13.8kPa ± 5% to the mouthpiece for 5 seconds, repeat 10 times, detect whether the projectile passes through the mouthpiece

Standard Accessories Included

• Mouth-Actuated Catapult Tester main unit

• Tube gripper, 3 pieces

• Pressure control system

• Cycle timer

• Operation manual

Items Excluded

• Calibration certificate (available upon request)

• Extended warranty (available for purchase)

• On-site installation and commissioning (available as a service)

• Test samples (mouth-actuated projectile toys)

Pre-installation Requirements

• Stable, level benchtop with adequate space for the unit and test samples

• Dedicated AC 220V, 50Hz power supply

• Compressed air source capable of delivering stable 13.8 kPa pressure (if required by the unit's pneumatics)

• Test samples prepared with mouthpieces compatible with the tube grippers

• Operator training on toy safety testing procedures is recommended

Key Benefits: Repeatable Blow-Through Checks Without Manual Pressure Guessing

Standards-Aligned Pressure Application

The Mouth-Actuated Catapult Tester applies 13.8 kPa ± 5% to the mouthpiece, matching the pressure specified in the test method. The pressure is held for 5 seconds per cycle, and the full sequence runs 10 times. You do not need to estimate whether you blew hard enough or long enough.

Tube Grippers for Secure Mouthpiece Connection

Three tube grippers are included to hold the toy's mouthpiece during pressure application. The connection stays sealed through all 10 cycles, so the pressure reaches the projectile rather than leaking around the tube.

Clear Pass/Fail Result

After the 10-cycle sequence, the operator inspects whether the projectile has passed through the mouthpiece. The test answers the safety question directly: can a child blow the projectile backward into their mouth? No force curves or software interpretation are required.

Compact Benchtop Footprint

The unit is configured as a benchtop station powered by standard AC 220V. Toy manufacturers can place it in incoming inspection or finished goods testing without dedicating a separate test room.

To explore how this Mouth-Actuated Catapult Tester fits into your toy safety testing workflow, visit our website at Optimum Solution to compare related Catapult Tester instruments. For detailed product information, you can view the GESTER mouth-actuated catapult tester product page on the manufacturer's site. For information on toy safety standards, refer to the EN 71-1 specification or the ISO 8124-1 standard.

Solving the Problems That Slow Toy Safety Qualification Down

Struggling to apply consistent pressure across different operators?
The pressure control system holds 13.8 kPa ± 5% for the full 5-second duration. Operators do not need to judge whether their breath pressure matches the standard.

Concerned about the mouthpiece slipping during the test?
Three tube grippers are included to secure the mouthpiece. The connection stays sealed through all 10 cycles, so the pressure reaches the projectile as intended.

Tired of testing only one or two cycles and hoping it is enough?
The unit runs the full 10-cycle sequence the method specifies. Each cycle applies the same pressure for the same duration, so the test reflects repeated use rather than a single attempt.

Need a clear result for a supplier qualification or regulatory submission?
The test produces a physical outcome: projectile passed through or did not pass through after 10 cycles at 13.8 kPa. The operator records the result, and the inspection is complete.

Warranty and Support

We provide a 1-year manufacturer's warranty covering parts and labor. Technical support, installation assistance, and operational training are also available. Replacement parts and consumables are available throughout the product's service life.

Call to Action

Request a Quotation or Technical Datasheet: Contact us for more information, customized configurations, and solutions tailored to your specific requirements.